150W DC Spiral Bevel Right Angle Brush Gear Motor
Solution Description:
Equipment Motor-Torque Desk Allowance Torque Device:Upside (N.m)/Belowside (kgf.cm)
•Gearhead and Intermediate gearhead are marketed independently.
•Enter the reduction ratio into the blank() within the product title.
•The velocity is calculated by dividing the motor’s synchronous speed by the reduction ratio. The true pace is two%~20% much less than the shown value, depending on the size of the load.
•To reduce the velocity outside of the reduction ratio in the subsequent table, connect an intermediate gearhead (reduction ratio: ten) between the reducer and motor. In that circumstance, the permissible torque is 20N.m.
|
Type Motor/Gearhead |
Gear Ratio |
3 |
three.6 |
5 |
6 |
7.5 |
nine |
12.5 |
fifteen |
18 |
25 |
thirty |
36 |
fifty |
60 |
75 |
ninety |
one hundred |
one hundred twenty |
one hundred fifty |
a hundred and eighty |
|
Pace r/min |
866 |
722 |
520 |
433 |
346 |
288 |
208 |
173 |
one hundred forty four |
104 |
86 |
seventy two |
fifty two |
forty three |
34 |
28 |
26 |
21 |
17 |
14 |
|
| Z5D150-24GU(5GU50RT) |
5GU()RC/ 5GU()RT |
.87 |
one.04 |
one.45 |
1.74 |
2.41 |
five.forty four |
four.02 |
4.eighty two |
5.78 |
8.03 |
nine.sixty four |
ten.four |
14.five |
17.four |
20. |
twenty. |
twenty. |
20. |
20. |
twenty. |
|
8.87 |
10.6 |
fourteen.8 |
seventeen.seven |
24.6 |
fifty five.5 |
41. |
forty eight.two |
59. |
eighty one.nine |
98.3 |
106 |
148 |
177 |
200 |
200 |
two hundred |
200 |
200 |
200 |
Dimensions(Unit:mm):
Firm Details
FAQ
Q: What’re your primary goods?
A: We at present generate Brushed Dc Motors, Brushed Dc Gear Motors, Planetary Dc Equipment Motors, Brushless Dc Motors, Stepper motors, Ac Motors and High Precision Planetary Equipment Box and so on. You can check out the requirements for earlier mentioned motors on our site and you can electronic mail us to advise required motors for each your specification as well.
Q: How to decide on a appropriate motor?
A:If you have motor photos or drawings to present us, or you have comprehensive specs like voltage, velocity, torque, motor size, functioning mode of the motor, necessary life span and sound level and so on, remember to do not wait to permit us know, then we can advocate ideal motor per your request accordingly.
Q: Do you have a CZPT provider for your standard motors?
A: Of course, we can customise per your request for the voltage, velocity, torque and shaft size/condition. If you need to have extra wires/cables soldered on the terminal or need to have to include connectors, or capacitors or EMC we can make it too.
Q: Do you have an personal layout service for motors?
A: Sure, we would like to design motors individually for our customers, but it could need to have some mould establishing price and design and style charge.
Q: What is actually your direct time?
A: CZPTly talking, our standard common item will need 15-30days, a bit lengthier for CZPT products. But we are really adaptable on the direct time, it will count on the distinct orders.
Make sure you contact us if you have thorough requests, thank you ()
